Search found 14 matches

by Tim
Fri Dec 09, 2016 10:19 pm
Forum: Electric Meters
Topic: Reset date and lost communication
Replies: 8
Views: 16054

Re: Reset date and lost communication

Reads were 100% before I tried to set the date. It's curious.
by Tim
Thu Dec 08, 2016 10:32 pm
Forum: Electric Meters
Topic: Reset date and lost communication
Replies: 8
Views: 16054

Re: Reset date and lost communication

Yes meter is 3435
about 3-4 out of 10 were successful.
by Tim
Wed Dec 07, 2016 7:53 pm
Forum: Electric Meters
Topic: Reset date and lost communication
Replies: 8
Views: 16054

Re: Reset date and lost communication

Here is the hex info after a bad read response: 20 30 30 30 20 30 30 30 30 30 30 30 30 34 38 33 35 30 31 31 36 31 32 30 37 30 34 31 37 34 35 31 31 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 ...
by Tim
Tue Dec 06, 2016 10:17 pm
Forum: Electric Meters
Topic: Reset date and lost communication
Replies: 8
Views: 16054

Re: Reset date and lost communication

Jameson Yes I was able to communicate prior to the date change. Yesterday 12/5: After changing the time and pressing ok, I received the bad response error. When I checked the time/date again it was a time and date in the future, i.e. set the time to 8 pm on 12/5, pressed ok, got a bad response error...
by Tim
Mon Dec 05, 2016 10:51 pm
Forum: Electric Meters
Topic: Reset date and lost communication
Replies: 8
Views: 16054

Reset date and lost communication

I had to change the date on my 25IDS meter and now it won't communicate with Dash. I get a "bad meter response" error. Additionally, the date changes on its own when I close out of the editor to a time in the future. I discovered this when reopening the editor.
by Tim
Tue Jan 12, 2016 9:55 pm
Forum: EKM Metering Systems
Topic: New Wifi/lost communications and iSerial login failure
Replies: 15
Views: 28906

Re: New Wifi/lost communications and iSerial login failure

Jameson, I sent the iSerial via usps on Monday. You should see it soon. Thanks, Tim
by Tim
Thu Jan 07, 2016 12:03 am
Forum: EKM Metering Systems
Topic: New Wifi/lost communications and iSerial login failure
Replies: 15
Views: 28906

Re: New Wifi/lost communications and iSerial login failure

My statements to no green light referred to your's and BlueHornet's 2012 procedures which indicated it should blink while resetting. It comes on once the Ethernet cable is plugged in, however, 2 of the procedures didn't note that it should be plugged back in during the procedure, but indicated the l...
by Tim
Tue Jan 05, 2016 10:33 pm
Forum: EKM Metering Systems
Topic: New Wifi/lost communications and iSerial login failure
Replies: 15
Views: 28906

Re: New Wifi/lost communications and iSerial login failure

Here's what I did. First I used BlueHornet's method from his post of October 16, 2012. 1. Disconnect the Ethernet cable 2. Disconnect the serial cable 3. Disconnect the power supply 4. Unscrew the two screws on each side on the unit and remove the cover 5. Locate the small white reset button, next t...
by Tim
Mon Jan 04, 2016 11:43 pm
Forum: EKM Metering Systems
Topic: New Wifi/lost communications and iSerial login failure
Replies: 15
Views: 28906

Re: New Wifi/lost communications and iSerial login failure

OK, so I guess at this point I've learned my lesson: don't listen to anyone's advice on this forum unless it's your advice. Unfortunately, that doesn't help me solve my problem. A problem, interestingly enough, that is still the same as it was from the beginning of this thread, namely, I cannot get ...
by Tim
Sun Jan 03, 2016 9:20 pm
Forum: EKM Metering Systems
Topic: New Wifi/lost communications and iSerial login failure
Replies: 15
Views: 28906

Re: New Wifi/lost communications and iSerial login failure

I had tried admin/system from an earlier recommendation without success. system/admin failed as well. I expected the hard reset would allow access with admin/admin, which is default, and I was told the reset restored the iSerial to defaults. Had I known this would not work I never would have reset i...